Hotline
Our Product

CAS 103-83-3

Overview:

Name: Dimethylbenzylamine

Alias: BDMA, N-dimthylbenzylamine, dimethylbenzylamine, benzyldimethylamine, catalyst BDMA, hard foam catalyst BDMA, N-benzyldimethylamine, BDMA, CAS 103-83-3, Dabco BDMA, Jeffcat BDMA , Lupragen N103, PC CAT NP60

Molecular formula: C9H13N;

Relative molecular mass: 135.20;

CAS number: 103-83-3;

Colorless to slightly yellow transparent liquid, soluble in ethanol, soluble in hot water, slightly soluble in cold water;

Purity ≥99%;

Moisture≤0.5%;

Viscosity (25℃): 90mPa.s;

Density (25℃): 0.897g/cm3;

Freezing point: -75℃;

Boiling range: 178-184℃;

Refractive index (25℃): 1.5011;

Flash point (TCC): 54℃;

Steam pressure (20℃): 200Pa

Physical and chemical properties

Appearance: colorless to light yellow liquid.

Solubility Slightly soluble in cold water, soluble in hot water, miscible in alcohol and ether.

Melting point -75 °C

Boiling point 183-184 °C 765 mm Hg(lit.)

Density 0.9 g/mL at 25 °C(lit.)

Refractive index n20/D1.501(lit.)

Flash point 130 °F

Storage conditions Flammables area

Water solubility 8 g/L (20 ºC)

BRN 1099620 A

High Quality BDMA / CAS 103-83-3 / Benzyldimethylamine / N,N-dimthylbenzylamine

High Quality BDMA / CAS 103-83-3 / Benzyldimethylamine / N,N-dimthylbenzylamine

use:

In the polyurethane industry, BDMA is a catalyst for polyester polyurethane block soft foam, polyurethane rigid foam, polyurethane sheet and adhesive coatings. It is mainly used for hard foam, which can provide polyurethane foam with good early fluidity and uniform cells. Good adhesion between foam and substrate;

In the field of organic synthesis, BDMA is mainly used as a catalyst for the synthesis of dehydrohalogen in organic drugs, corrosion inhibitors, acid neutralizers, accelerators for embedding electron microscope slices, etc.;

BDMA is also used to synthesize quaternary ammonium salts and produce cationic surface active powerful fungicides, etc.;

In terms of epoxy resin, BDMA is mainly used to promote curing systems such as anhydrides, polyamides, and fatty amines to accelerate product curing. It is widely used in epoxy resin potting materials, encapsulating materials, epoxy floor coatings, and marine paint Used as curing accelerator;

Specific application examples of BDMA are: carbon fiber/monomolecular epoxy resin-based composite laminates, electrophoretic coatings of epoxy substrates, and dry-type transformer encapsulants;

 

Alias:

Dimethylbenzylamine Benzyldimethylamine BDMA 103-83-3 Dabco BDMA Jeffcat BDMA Lupragen N103 PC CAT NP60

 

Storage and transportation:

Should be sealed and stored in a dry, cool and ventilated warehouse

 

package:

200KG/drum Storage: It is recommended to store in a dry and cool area with proper ventilation. After the original packaging, please fasten the packaging cover as soon as possible to prevent the water and other substances from mixing into the product and affecting its performance. Do not breathe dust, avoid skin and mucous membrane contact. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothing separately and wash it before reuse. Maintain good hygiene habits.

Company Name: Shanghai OHANS Chemical Co., Ltd.
Sales Manager: Hunter
E_Mail:  Honda@ohans.com
Telephone: +86-021-5161 9971

+86-021-5161 9972

+86-021-5161 9973

Address: 709 Lingshi Road, Zhabei District, shanghai, China
Website: www.dpta.vip

PU Catalyst: BDMA (benzyldimethylamine) CAS:103-83-3

Over view:

Common Name: Benzyl Dimethyl Amine

Other Chemical Names: N,N-Dimethylbenzylamine, Benzenemethamine, N,N-dimethyl-;Benzenemethanamine,N,N-dimethyl-;Benzylamine,

Physical and chemical properties:

Appearance Form: transprant light yellow  liquid
Odour no data available
PH 10 at 10 g/l at 20 °C
Melting point/freezing point Melting point/range: -75 °C – lit.
Initial boiling point and boiling range 181 – 184 °C at 1.020 hPa – lit.
Flash point 53 °C – closed cup
Evaporation rate no data available
Flammability (solid, gas) Upper explosion limit: 6,3 %(V)
Upper/lower flammability

or explosive limits

Lower explosion limit: 0,9 %(V)
Relative density 0,9 g/cm3 at 25 °C
Water solubility soluble
Partition coefficient: noctanol/water log Pow: 1,87
Molar formular C9H13N
Molar mass 135.21

Features and uses:

A liquid tertiary amine catalyst. Can improve foam cure and demolding time. It is an excellent candidate to consider for use in water-NCO reaction in rigid polyurethane foams.

BDMA is typically suitable to replace DMCHA in formulations using a high level of water as blowing or co-blowing agent can reduce surface friability and improve adhesion of foam to substrates.

BDMA promotes the urethane reaction and is commonly used in high-water rigid foam applications to reduce friability. It has a characteristic but low amine odor, and is soluble in water and in most organic solvents.

BDMA is used in flexible slabstock and rigid foam applications.

It promotes the urethane reaction and is commonly used in high-water rigid foam applications to reduce friability.

BDMA is also used for flexible slabstock foam applications.

Storage Information 

Recommends that our catalysts be stored in a dry and cool area under appropriate ventilation conditions. Each container should be closed tightly to avoid contamination with moisture or other negative influences that could change the products’ performance in the end use.

 

Package:

180KG/Steel Drum

(DABCO BDMA/Niax BDMA/ PC Cat NP60/ Addocat DB/ Jeffcat BDMA/ Lupragen N103)Our Company

Since its establishment, the company has adhered to the service tenet of “integrity-based, customer first”, adhered to customer demand as the focus, market-oriented, adhered to technological innovation, management innovation and service innovation, and constantly implemented lean production, refined management, to provide customers with better products and services! The company has its own factory, research and development base, set up a strict scientific quality management system, and constantly committed to technological innovation, product innovation and management innovation, so as to ensure that our products have a certain competitiveness in the same industry. The factory is located in Jining City, Shandong Province, China, covering an area of 500 acres, and the current production capacity of various types of amines is 5,000 to 10,000 tons per year.

Our Advantages

Strict Quality Management
Our company strictly implements ISO9002 quality management standards and has established a complete quality management system to ensure the long-term stability of product quality.

Efficient Service
Our production is efficient and reliable, so we deliver on time and within delivery deadlines. At the same time, our team is always happy to help customers and strive to solve customer problems in a short time.

Competitive Price
We have long-term services in wholesale Polyurethane catalyst and have established long-term and stable cooperative relationships with many retailers and agents to provide our customers with reasonably priced products.

OEM Available
Our employee team has high R&D capabilities, superb design and development capabilities, skilled manufacturing technology, and rich product application experience, and can also meet OEM business needs.throughout the entire industry chain.

Tags:
Prev:
Next: